-40%

Rearend Narrowing Fixture Bushings - 10 bolt GM Rear End with 9" Ford 3.15" Ends

$ 63.35

Availability: 32 in stock
  • Return shipping will be paid by: Buyer
  • Condition: New
  • Manufacturer Part Number: 10 bolt GM Narrowing Kit
  • Restocking Fee: No
  • Returns Accepted: Returns Accepted
  • Item must be returned within: 30 Days
  • Refund will be given as: Money Back
  • Brand: LMP

    Description

    Here we have the tools needed to hold a 10 bolt GM rearend housing in alignment when you are narrowing, assembling or changing the width using 9" Ford 3.15" or 2.835" housing ends.
    So we are clear here, you are building a 10 bolt GM housing, but cutting the ends off and replacing them with the Big or Small Ford 9" housing ends. You will be using aftermarket axles, not the original c-clip style axles. ( if you want to narrow a stock housing and use stock c-clip axles, I have these kits also. Check my other listings)
    Included are.....
    One pair of housing end bushings or rings that fit the Big Ford housing ends that use the 3.15" o.d. bearing or the Small Ford housing ends that use the 2.835" o.d. bearings.
    One pair of lock rings to hold the above bushings in place on the shaft.
    And one pair of bushings or rings that would fit in the 10 bolt GM differential case that measures 2.891". These bushings fit where the differential bearings would normally be. (LM102949/LM102910)
    All three are designed to be used with a 1 1/4" o.d. alignment shaft and the bushings are machined from 6061 aluminum right here in good old Missouri.
    6061 aluminum is the material of choice for Dart aluminum engine blocks, Aeroquip AN fittings, aluminum racing flywheels, OHC camshaft sprockets, etc. These are just bushings and will see no wear or abuse and should last a lifetime.
    The 1 1/4" shaft
    IS NOT
    included in this listing.
    Due to the high shipping cost of a solid steel bar five feet long , we suggest you source the alignment bar locally or online. Most people use a 1 1/4" o.d. 1018 solid steel cold rolled shaft 60" – 72” in length. The common bar diameter of 1018 cold rolled steel is 1.248” and works well. The industry standard for 1018 round bar is .002” smaller than the stated diameter. Chrome Moly, Stainless Steel and tubing may be larger than the 1.248" required. SpeedyMetals, OnlineMetals and DiscountSteel are a good source for the bar although you should be able to source it from a local welding or steel shop. Obviously the shaft needs to be straight, not rusty and the proper length for your project.
    Lightly lubricate the bar with oil.
    We also have kits for 10 bolt GM, 12 bolt GM, 7.5" GM, 10 & 12 bolt GM,
    57-64 Olds, 59-64 Pontiac,
    8 3/4" Mopar, Dana 35, Dana 44, Dana 60, 8" Ford, 8.8" Ford and 9" Ford. Check our other listings.
    Check our other listings for more rear axle, frame and suspension parts.
    If you have any questions you can contact us through eBay Messages.
    Here is why you cannot find my phone number listed on Ebay anymore........
    Buyers and sellers should always use eBay messaging tools (My Messages, Best Offer) to communicate with one another. By September 2017, sellers will no longer be allowed to include contact information, such as email, phone numbers, and social media links, in item descriptions, titles, or other eBay pages.
    Will combine shipping when feasible.
    Shipping to the lower 48 states only.
    No overseas shipping.
    Concerning Returns – Buyer is responsible for return shipping – 10% will be deducted from refund to cover fees
    Attention California Residents:
    WARNING:
    This store sells products that may contain chemicals which are known to the State of California to cause cancer, birth defects, or other reproductive harm. By ordering products for delivery into California, you acknowledge that you have received this warning.
    Please feel free to contact us should you have any questions.
    For more information, go to www.P65Warnings.ca.gov.